iPhone 6 Plus Loud Speaker Replacement in 4 Minutes

Today I’m going to show you how to fix the loud speaker on your iPhone 6 Plus.

If you want to see any of the other repair videos go ahead and click the links in the

front of this one.

To get to the loud speaker on your iPhone 6 Plus, we’re going to go underneath the


Grab your pentalobe screwdriver and take out the bottom two screws.

If you need any tools or parts for this project go ahead and look in the video description


I will have everything linked for you there.

Grab your suction cup and lift up on the screen a little bit – just so you can slide your

pry tool underneath.

And then pry up on the edge of the screen which is where the frame is and also the frame

of the phone.

You don’t want to put any pressure on the screen or else you’re going to bend it or

break it and that’s a more expensive repair if you end up breaking that.

Don’t bend the screen past 90 degrees or else you’ll hurt the ribbon cables underneath

this metal plate.

Take off those 5 screws, remove the plate, and then you’re going to unsnap each of

these little ribbon cables.

You don’t technically have to take off the screen for this repair, but it does make it

easier because any twist of the screen will damage these cables.

So you want to be gentle with it.

Set the screen off to the side.

And then you have the 3 screws on the little metal part that’s next to the battery.

Then you can remove the top metal plate.

Unclip the battery from the rest of the phone and lift up the little ribbon cable because

there’s another screw hiding underneath there.

Once you remove that screw, it’s attached to the vibrating motor, unclip the little

wire cable and then the vibrating motor clips out.

You can pull the wire cable out from the vibrating motor – it’s got a little slot right there.

You can see the vibrating motor here, it’s got the two little connection points that

just clip down onto the wire cable that goes down to the charging port.

Keep on lifting that wire cable out from the loud speaker.

Two screws down there at the bottom of the loud speaker.

Then once those are out it frees the loud speaker to come away from the phone.

Pretty straightforward.

So this is how you take out the loud speaker.

You can clean it out if there are ever any metal shavings or if it’s been water damaged.

There are two contact points that go onto the charging port cable.

So if you replace the loud speaker and it still doesn’t work, you might need to replace

the charging port cable as well.

Anyway, got that metal bracket back onto the loud speaker.

And then I’m putting the wire cable in-between the metal bracket and the loud speaker itself

so that it never gets damaged with the battery.

Screwing in the screw at the corner of the battery, and then also at the corner of the

loud speaker down there in the other corner of the phone.

Pinching the wire cable into the vibrating motor.

Getting that one hidden screw put back in.

Clipping down the ribbon cable.

Clipping down the wire cable.

Then making sure it’s completely clipped into place or else you’ll get interference

later on.

And then clipping on the battery.

Once the battery is clipped in you can put on that top metal plate and the bottom screw

for the vibrating motor.

Then you have the screen.

Make sure you’re super careful with these connections as you pinch them back into place.

If any of the connections on aren’t fully seated onto the main board, you’re going

to have lines running through your screen.

If that happens, go ahead and turn off your phone again, lift up the screen and then reseat

the cables.

That’s usually how you fix the lines.

So I’m just kind of putting them over the top of the connection and then pressing down,

treating them like Legos, pushing them down all the way making sure they’re secure.

I folded down the screen and then turned on the phone just to make sure there were no


Now I’m going to turn off the phone again because you definitely don’t want to work

on it while it’s not seated down into the frame.

Now that I know there are no lines I can go ahead and get these 5 screws back in.

And then there are some grooves along the top of the screen.

Go ahead and press that into the frame.

Make sure it’s flush and secure and then you can run your fingers down along the edge

of the phone, pressing that down into the back of the frame as well.

Just be super careful because screens are very fragile, especially with a phone this


You do risk breaking it if you press too hard or in the wrong place.

Make sure you stick around the frame of the phone.

Get those bottom two pentalobe screws back in and you are set.

If you have any questions make sure to leave them in the comments below.

Make sure to “like” if this video helped you and don’t forget to subscribe.

It does mean a lot to me.

And don’t forget to check out my Instagram, I think it’s pretty fun.

Thanks a ton for watching.

Hope to see you around!